Airflow difference
At 90 PSI, the published delivery changes from 5.3 CFM on the 20020 to 5 CFM on the 20020CR. Compare those ratings with your tool’s at-load demand and usage pattern.
20020 VS 20020CR
Similar names, different duty claims
The CR designation matters. Compare 70/30 guidance with the CR model’s duration-specific continuous-run claims.
| What to compare | 20020 | 20020CR |
|---|---|---|
| Air delivery at 90 PSI | 5.3 CFM | 5 CFM |
| Tank volume | 20 US gal | 20 US gal |
| Duty share | 70% — see manual | 100% — see manual |
| Published noise* | 70 dB | 77 dB |
| Pump type | oil-free | oil-free |
| Weight | Not confirmed | Not confirmed |
| Supply voltage | 110 V | 110 V |
*Noise readings are manufacturer figures; measurement methods and distances are not consistently available.
Storage difference
The tanks are 20 and 20 US gallons. Over the same pressure interval, stored free-air volume scales with tank volume. Recovery time also depends on delivery across that interval and is not inferred here.
Limits that remain part of the choice
20020: 70% running / 30% stopped across a standard workday; additional continuous-use limits apply.
20020CR: 100% duty; duration limited by pressure.
- Product feature list says 114 lb; additional-information table says 115 lb. weightLb is null pending confirmation.
- Product page describes 90–120 PSI working pressure, ±5 PSI; maximum tank pressure is 125 PSI.
- Product features say 114 lb and 20 × 20 × 45 in; additional information says 130 lb and 21 × 21 × 50 in without clearly labeling package values. weightLb and dimensionsIn are null pending clarification.
- Extension-cord conflict: product page says 14 AWG up to 100 ft; linked manual says 14 AWG up to 25 ft. Follow the manual supplied with the exact unit and manufacturer clarification; do not promise 100 ft.
CHECK THE PAIRING
Your tool. Your working schedule.
Example schedule: 10 trigger seconds each minute. Change it to reflect your job.
Usage conditions need review
Average flow is within the published delivery rating, but burst demand, duty data or operating limits still need checking. This is not a compatibility approval.
Your average air demand3.67 CFM10 seconds of trigger time per minute · 1 tool · 30-minute session
Published compressor delivery5.30 CFMAt 90.0 PSI
Manufacturer application limits
For referenceNo category restriction is recorded in this dataset. Check the model manual for your application.
Working pressure
Within this criterionThe tool’s 90 PSI requirement is within the compressor’s 125 PSI pressure ceiling. This does not establish pressure delivered through the regulator, hose and fittings.
Air demand versus published delivery
Within this criterionThis schedule averages 3.67 CFM against 5.3 CFM at 90 PSI. This checks average air balance, not pressure throughout each trigger pull.
Airflow during a trigger pull
Check the conditionsWhile the trigger is held, 22 CFM exceeds the 5.3 CFM delivery rating. Stored air may help a short burst, but pressure-switch behavior, burst length and losses have not been simulated.
Pump duty
Within this criterionA simplified air balance implies 69.18% pump-on time; the recorded duty share is 70%. 70% running / 30% stopped across a standard workday; additional continuous-use limits apply. This is not a measured cycle or a continuous-use approval.
Session duration
Check the conditions30 minutes is recorded for your planned session. Model-specific duration limits, cooling breaks and actual cycling are not automatically validated. This field does not change the airflow calculation.
Hose and connections
Check the conditionsThe tool specifies a minimum 0.38-inch hose inside diameter; its recorded air inlet is 0.25 inch. Confirm thread type, coupler profile, hose length and available flow separately; matching nominal sizes alone is not a connection check.
Calculation details
69% estimated pump-on share from average demand ÷ rated delivery. This is an air-balance estimate, not an observed duty cycle or permission to run continuously.
14.9 seconds of theoretical stored-air drawdown over 120 → 90 PSI, with the pump off and a continuous trigger pull. This is not actual operating time, recharge time, or storage life.
Specification screening only. Actual pressure at the tool, hose losses, pump cycling and installation conditions are not established by an average-flow calculation.
Usage conditions need review
Average flow is within the published delivery rating, but burst demand, duty data or operating limits still need checking. This is not a compatibility approval.
Your average air demand3.67 CFM10 seconds of trigger time per minute · 1 tool · 30-minute session
Published compressor delivery5.00 CFMAt 90.0 PSI
Manufacturer application limits
For referenceNo category restriction is recorded in this dataset. Check the model manual for your application.
Working pressure
Within this criterionThe tool’s 90 PSI requirement is within the compressor’s 125 PSI pressure ceiling. This does not establish pressure delivered through the regulator, hose and fittings.
Air demand versus published delivery
Within this criterionThis schedule averages 3.67 CFM against 5 CFM at 90 PSI. This checks average air balance, not pressure throughout each trigger pull.
Airflow during a trigger pull
Check the conditionsWhile the trigger is held, 22 CFM exceeds the 5 CFM delivery rating. Stored air may help a short burst, but pressure-switch behavior, burst length and losses have not been simulated.
Pump duty
Within this criterionA simplified air balance implies 73.33% pump-on time; the recorded duty share is 100%. 100% duty; duration limited by pressure. This is not a measured cycle or a continuous-use approval.
Session duration
Check the conditions30 minutes is recorded for your planned session. Model-specific duration limits, cooling breaks and actual cycling are not automatically validated. This field does not change the airflow calculation.
Hose and connections
Check the conditionsThe tool specifies a minimum 0.38-inch hose inside diameter; its recorded air inlet is 0.25 inch. Confirm thread type, coupler profile, hose length and available flow separately; matching nominal sizes alone is not a connection check.
Calculation details
73% estimated pump-on share from average demand ÷ rated delivery. This is an air-balance estimate, not an observed duty cycle or permission to run continuously.
14.9 seconds of theoretical stored-air drawdown over 120 → 90 PSI, with the pump off and a continuous trigger pull. This is not actual operating time, recharge time, or storage life.
Specification screening only. Actual pressure at the tool, hose losses, pump cycling and installation conditions are not established by an average-flow calculation.
Manufacturer sources
Checked 25 October 2026. Specifications can change; verify the exact model and market before purchase.